= el9 dmesg stops here due to lack of drivers, Fedora 34 dmesg output continues below = usb 2-1: New USB device strings: Mfr=3, Product=1, SerialNumber=2 usb 2-1: New USB device found, idVendor=2040, idProduct=826d, bcdDevice= 1.00 usb 2-1: new high-speed USB device number 6 using xhci_hcd If any other drivers are needed, would it be possible to make them available as well? Thank you so much for considering this request! I am also not sure if any other drivers are needed (for example, lgdt3306a, tveeprom, and dvbdev are listed as well, but I wasn't sure if these were drivers/modules). Would it be possible to make the em28xx driver available? An ELRepo el9 package for the si2157 driver is already available (kmod-si2157), but there is no package for the em28xx driver yet. I can see that the em28xx driver is needed, as is the si2157 driver. I have included the dmesg output from Fedora 34 below for reference. I booted my system using a Fedora 34 Live DVD just to confirm that the adapter should work in kernel 5.14, and it does indeed appear to work. The tuner itself is identified by lsusb as follows:īus 001 Device 007: ID 2040:826d Hauppauge 955DĪfter plugging in the adapter, dmesg shows messages indicating there is a new USB device, but that's about it (no drivers are loaded and the adapter is not usable). I was wondering if it would be possible to get kmod packages for the necessary drivers? All of the necessary drivers appear to exist in the kernel source, they simply are not compiled and available for use in the el9 kernel. I am attempting to install a Hauppauge WinTV-dualHD USB tuner on an el9-based system (in this case, AlmaLinux 9), and it appears that all of the necessary drivers are no longer included by default in the upstream kernel. As with over-the-air TV signal strength, if the signal Quality is low, you might want to check your cable system in your home and either remove splitters (each splitter you have on a home cable network lowers the signal strength) or use a "cable TV signal booster".0001302: Possible to build kmod-em82xx (and possibly a few others) for TV tuner support in el9? If you are watching clear QAM digital cable TV or DVB-C, you can use the WinTV's signal quality display to see the reception quality of that channel. Using the Signal Monitor to monitor the quality of a digital cable TV channel Here are some tips from our TV Troubleshooting guide to help optimize the TV reception for over-the-air signals. In this case, you might want to consider an antenna "booster" or a better TV antenna. If you cannot get a good TV picture after positioning the antenna, the digital TV signal is too weak to receive a Digital TV program without distortion. The higher the percentage, the better the TV signal is. In WinTV, look at the Quality indicator, and position your antenna to maximize the Quality.This might require a longer antenna cable, but if your antenna is not pointing at the TV transmitter, you will not get good reception. If you have a flat window style antenna, pick a window which is 'pointing' to the TV transmitter.The higher up from the floor your antenna is, the better the signal strength will be.The best positions of the antenna are those where there is a clear view to the TV transmitter.The digital signal quality will be displayed as a % (percent) of the maximum signal quality possible Run WinTV v10 and tune to the TV channel where you have the best TV picture.Using the WinTV Quality Monitor to adjust a digital TV antenna The Signal Quality Monitor is a handy tool which can be used to either adjust your digital TV antenna, or when used with digital cable TV, to know if your digital signal is too weak to receive a signal without distortion. It will not work with analog TV channels. Note: The Digital Quality Monitor will work with ATSC and QAM digital TV channels plus DVB TV channels on most Hauppauge digital TV tuner boards. The key indicator is Quality which shows the relative quality of the TV channel which is being displayed in the WinTV window. To show the signal quality, tune to a TV channel and hit 'CTRL-D'. The signal quality monitor is part of the WinTV v10 application. Overview of the Digital Signal Monitor for Hauppauge TV tuners Strong Signal 98% Good signal 88% Good signal 84% OK signal 82% Good reception - roof and window Good reception roof, bad reception window Bad reception roof and window The WinTV Signal Quality Monitor displays the relative quality of the digital signal on the channel you are tuned to.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |